Master the 210-065 Implementing Cisco Video Network Devices v1.0 content and be ready for exam day success quickly with this Actualtests 210-065 exam prep. We guarantee it!We make it a reality and give you real 210-065 questions in our Cisco 210-065 braindumps.Latest 100% VALID Cisco 210-065 Exam Questions Dumps at below page. You can use our Cisco 210-065 braindumps and pass your exam.
Q31. Which four features are supported by Cisco TelePresence Server for all hardware models in remotely managed mode? (Choose four.)
C. Cluster sizes of more than 5 servers
E. Active presence for all devices
F. Support for Conductor
G. Native scheduling capabilities
Q32. A customer has a data and VoIP converged network and would like to add video to this network. Which two key QoS elements should be included in the new network design? (Choose two.)
A. Configure bandwidth management features to smooth bursty traffic and mitigate end-to-end congestion.
B. Assign a high priority to transactional traffic to maintain quality of business traffic.
C. Keep video traffic on the low latency queue and move voice traffic to a lower-priority queue.
D. Apply bandwidth control features that will guarantee bandwidth for the maximum possible amount of video traffic.
E. Assign both video and voice traffic to use the highest-priority queue.
Q33. Which two additional items must be configured for an endpoint to register manually with the Cisco TelePresence Video Communication Server for the SIP to function correctly? (Choose two.)
A. E.164 alias
B. H.323 ID
C. SIP uniform resource indicator
D. configured SIP registrar and proxy server
E. NTP server IPv4 address
F. unique system ID
Q34. Which two additional items can be configured for an endpoint to register with the Cisco TelePresence Video Communication Server for H.323 to function correctly? (Choose two.)
A. unique system ID
B. unique H.323 ID
C. unique DNS entry ID
D. unique E.164 alias
E. unique real-time transport protocol port numbers
F. unique NTP server IPv4 address
Q35. Which statement is true about the Cisco TelePresence System 500-32 system regarding the HVAC needs for the room where it is installed?
A. The system does not require any additional requirements above the normal HVAC requirements for the room.
B. You must supply additional cooling requirements for the room.
C. You must supply a room that has energy-efficient lighting to reduce the temperature of the room.
D. The temperature of the room will be 10 to 20 degrees warmer than the rest of the building.
Q36. When placing a call from Cisco Jabber Video for TelePresence to the Cisco TelePresence System Codec C40, which FECCs are available?
A. Only zoom-in and zoom-out are available.
B. Only left and right are available.
C. Only up and down are available.
D. No FECC is available.
E. Left, right, up, down, zoom-in, and zoom-out are all available.
Q37. What is the main difference between a Cisco TelePresence Multipoint Control Unit and a Cisco TelePresence Multipoint Switch?
A. The Cisco TelePresence Multipoint Control Unit is a hardware bridge. The Cisco TelePresence Multipoint Switch is a software bridge.
B. The Cisco TelePresence Multipoint Control Unit is a software bridge for immersive and non-immersive endpoints. The Cisco TelePresence Multipoint Switch is a hardware bridge for non-immersive endpoints.
C. The Cisco TelePresence Multipoint Control Unit delivers automatic voice-activated switching. The Cisco TelePresence Multipoint Switch provides active presence.
D. The Cisco TelePresence Multipoint Control Unit has a latency of less than 10 ms, whereas the Cisco TelePresence Multipoint Switch has a latency of 100 ms.
Q38. Refer to the exhibit.
Which two of these can cause the phone status error icon that is shown in the exhibit? (Choose two.)
A. The Cisco Unified Communications Manager IM and Presence Service is not available.
B. The username and password in Cisco Jabber phone services are misconfigured.
C. The Cisco Jabber initial audio and video settings need to be set.
D. There is no DN configured for the Cisco Unified Client Services Framework in Cisco Unified Communications Manager.
E. The Cisco Jabber does not have the correct phone button template and hence cannot register to the Cisco Unified Communications Manager.
F. The called user presence status is unknown.
Q39. The user of a Cisco TelePresence MX300 wants to control the far-end camera of any video conference participant. Which control device and function is used to control the far-end camera?
A. Navigate using the TRC5 Remote Control arrow keys.
B. Tap on the image of one of the participants using touch control.
C. Use the Touch Control Conference functions.
D. Use the TRC5 Remote Control home key.
Q40. Which two layout or switching modes are supported with the Cisco TelePresence Multipoint Switch? (Choose two.)
A. enhanced continuous presence
B. active speaker switching
C. continuous presence
D. speaker switching
E. room switching
F. active continuous presence
To know more about the 210-065, click here.